Saturday, September 29, 2012

Plinko Board

I work with children as a Cub Scout den leader and as a Primary Music Leader. Before I started working with these little ones, I knew that I have a penchant for being boring sometimes; now that I'm working with them regularly, they kindly let me know whenever they are the slightest bit bored.
I know, they're considerate like that.

To combat my inherent boring-ness, I decided to make a Plinko board to work into games and other activities. In Singing Time at primary, I think I'll call it Plink-go Sing-o!



In case you're interested, here's an overview of what I did:

1. Gather Materials

I used the following:
  1. Pegboard - I bought a 4' x 4' piece and had it cut in half (for about $1 more than a single 2' x 4' piece at Lowe's, so under $9 for both pieces)
  2. Wood to frame it - I used two pieces of 1" x 2" x 8' (about $1 each)
  3. Dowels for the pins - I used ten 1/4" x 4' dowels that I cut by hand (because I'm a masochistic miser, apparently, and this saved me a few dollars--my cost was $6 total for the dowels), but you can likely find pre-cut 1/4" x 1.5" dowel pins.
  4. Dot stickers - I used these to mark my layout plan on the back
  5. Paint - I used a combination of super-cheap spray paint and acrylic paint
  6. Ping pong balls

2. Prepare Wood

 I cut the 1x2 pieces to length (two 4' pieces; two 2' pieces) using a miter box set at 45 degrees for nice corners. They're shown here against the 2' x 4' pegboard.


I also cut about 300 1.5" dowel pins in the miter box, but I tried to be smart about it. I bundled the dowels together (with a zip tie) as a single piece of wood and used a small template block of wood to help keep the lengths consistent. Take a look:


I then enlisted my son to help me quickly sand the ends of the dowels where they were rough:


3. Assemble Wood Pieces

I wanted the frame pieces to be flush with the outside edge of the pegboard. Unfortunately, the spacing of the pegboard holes didn't work, so I simply drilled pilot holes 5/16" (which is half the width of the "1 inch" side of the 1" x 2") in from the edge at strategic locations (using a 7/32" bit).

After carefully positioning the frame pieces, I drilled pilot holes through the pegboard pilots into the wood, sunk wood screws, and added additional frame pieces using a dab of wood glue at the corners. Here's how it looked:


And a close-up of a corner:


4. Layout Pin Design

I planned my design on the computer (using Excel, which helped me know how many dowel pins I would need), but I wanted to see what it would look like on the board. I used round dot stickers to do this. As an added bonus, I figured the stickers would help me to get the pins in the right holes, and they might even help keep wood glue from leaking out the back when I glued the pins in.

Here's the layout design on the back of the board:


5. Attach Dowel Pins

To glue the dowel pins in the pegboard, I dipped the pin in a small reservoir with wood glue in it (I used a cleaned milk container lid, put them in place, and lightly tapped them with a hammer to seat them fully. Some aren't as straight as they could be, but imperfections preserve the DIY feel to this project!



6. Paint the Board

I used white spray paint as a base with the intention of adding a personalized touch afterward. Here's my spray paint station:


And here's my team helping to add a touch of color. They used Q-tips to put dots of different colors of acrylic paint on the tips of the dowel pins:





Add a nice border, and it's done!



7. Test

The final step is to ensure that it still works after adding all the paint:



The only remaining step is to have fun with it and keep it from falling apart!

1 thought:

limz said...

love it!!! thank you for sharing and the detailed instructions are easy to follow.